• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Protective clothing – General Requirements (ISO 13688:2013, IDT) (First revision)
MS ISO 13688:2020
Status : 1st Revision
Format : PDF

This International Standard specifies general performance requirements for ergonomics, innocuousness,
size designation, ageing, compatibility and marking of protective clothing and the informati ....Read more on to be
supplied by the manufacturer with the protective clothing.
This International Standard is only intended to be used in combination with other standards containing
requirements for specific protective performance and not on a stand-alone basis. Close

RM 45.00

Document will be sent via email



 Add To Cart
Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 1: Principles and specifications for machinery manufacturers (ISO 14123-1:2015, IDT) (First revision)
MS ISO 14123-1:2020
Status : 1st Revision
Format : PDF

This part of ISO 14123 establishes principles for the control of risks to health resulting from hazardous
substances emitted by machinery.
This part of ISO 14123 is not applicable to subst ....Read more ances that are a hazard to health solely because of their
explosive, flammable or radioactive properties or their behaviour at extremes of temperature or pressure. Close

RM 30.00

Document will be sent via email



 Add To Cart
Safety of machinery - Reduction of risks to health resulting from hazardous substances emitted by machinery - Part 2: Methodology leading to verification procedures (ISO 14123-2:2015, IDT) (First revision)
MS ISO 14123-2:2020
Status : 1st Revision
Format : PDF

This part of ISO 14123 establishes a methodology that leads to the selection of critical factors relating
to emissions of hazardous substances for the purpose of specifying suitable verification ....Read more procedures.
This part of ISO 14123 is intended to be used in conjunction with ISO 14123-1 and relates specifically to
ISO 14123-1:2015, Clause 8. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized orthermoplastic - Determination of compression set - ICS: 83.060 © Copyright 2020 DEPARTMENT OF STANDARDS MALAYSIA Descriptors: rubber, vulcanized rubber, thermoplastic rubber, compression set, low temperature Part 2: At low temperatures (Second revision) (ISO 815-2:2019, IDT)
MS ISO 815-2:2020
Status : 2nd Revision
Format : PDF

This document specifies two methods for the determination of the compression set characteristics of vulcanized and thermoplastic rubbers at low temperatures.
Method 1 derives from the methodolog ....Read more y used in ISO 815-1. Method 2 uses a specified testing device, allowing to measure and record the test piece thickness during recovery. Due to the load applied during recovery in method 2, no correlation can be established between the results given by both methods.
NOTE When rubber is held under compression, physical or chemical changes that prevent the rubber returning to its original dimensions after release of the deforming force can occur. The result is a set, where the magnitude of which depends on the time and temperature of compression as well as on the time, temperature, and conditions of recovery. At low temperatures, changes resulting from the effects of glass hardening or crystallization become predominant and, since these effects are reversed by raising the temperature, therefore, the measurements are always taken at the test temperature. Close

RM 45.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Determination of compression set - Part 1: At ambient or elevated temperatures Descriptors: rubber, vulcanized, thermoplastic, determination, temperature, compression set (Second revision) (ISO 815-1:2019, IDT)
MS ISO 815-1:2020
Status : 2nd Revision
Format : PDF

This document specifies methods for the determination of the compression set characteristics of
vulcanized and thermoplastic rubbers at ambient (one method) or elevated temperatures (three
....Read more methods, A, B, and C, depending on the way the test piece is released at the end of the test).
The methods are intended to measure the ability of rubbers of hardness within the range 10 IRHD to
95 IRHD to retain their elastic properties at specified temperatures after prolonged compression at
constant strain (normally 25 %) under one of the alternative sets of conditions described. For rubber of
nominal hardness 80 IRHD and above, a lower compression strain is used: 15 % for a nominal hardness
from 80 IRHD to 89 IRHD and 10 % for a nominal hardness from 90 IRHD to 95 IRHD.
NOTE 1 When rubber is held under compression, physical or chemical changes that prevent the rubber
returning to its original dimensions after release of the deforming force can occur. The result is a set, the
magnitude of which depends on the time and temperature of compression as well as on the time, temperature,
and conditions of recovery. At elevated temperatures, chemical changes become increasingly more important
and lead to a permanent set.
NOTE 2 Short-time compression set tests, typically for 24 h, at elevated temperatures are commonly used as
a measure of the state of cure, a means of material classification, and a specification to ensure the quality of a
compound. Longer tests, typically for 1 000 h, at elevated temperatures take account of the effect of ageing and
are often used to predict service performance, including that of sealing materials. Short-time tests at ambient
temperature show mainly the effect of physical changes (re-orientation of the molecular chains and the fillers). Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized - Determination of creep in compression or shear (First revision) (ISO 8013:2019, IDT)
MS 8013:2020
Status : 1st Revision
Format : PDF

This document specifies a method for the determination of creep in vulcanized rubber continuously subjected to compressive or to shear forces. The standard cannot be used for intermittent deformation ....Read more of rubber. Close

RM 45.00

Document will be sent via email



 Add To Cart
Rubber and plastics test equipment - Tensile, flexural and compression types (constant rate of traverse) - Specification (First revision) (ISO 5893:2019, IDT)
MS ISO 5893:2020
Status : 1st Revision
Format : PDF

This document specifies requirements for tensile-testing systems operating at constant rate of traverse and suitable for testing rubbers, plastics and adhesives, although any one system might only be ....Read more applicable to a narrower range of materials. It also covers such systems when used for flexural, shear and compression tests. Close

RM 15.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized - Determination of adhesion to wire cord (Second revision) (ISO 5603:2017, IDT)
MS ISO 5603:2020
Status : 2nd Revision
Format : PDF

This document specifies two methods for determining the adhesion strength of vulcanized rubber to wire cord which is embedded in the rubber.
The two methods do not necessarily give the same resu ....Read more lts.
They are applicable primarily to test pieces prepared in the laboratory under standard conditions and used for the development and control of materials and processes utilized in the manufacture of products reinforced with wire cord.
NOTE The methods can also be used for single wire, for example bead wire.
Method 1 reduces the dependence of the measured adhesion on the modulus and strength properties of the rubber. Close

RM 45.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Resistance to weathering (Second revision) (ISO 4665:2016, IDT)
MS ISO 4665:2020
Status : 2nd Revision
Format : PDF

This International Standard specifies methods for the exposure of vulcanized or thermoplastic rubbers
to natural or artificial weathering and methods for the determination of changes in colour, ....Read more appearance,
and physical properties resulting from exposure. Close

RM 30.00

Document will be sent via email



 Add To Cart
Rubber, vulcanized or thermoplastic - Methods of test for staining in contact with organic material (Second revision) (ISO 3865:2020, IDT)
MS ISO 3865:2020
Status : 2nd Revision
Format : PDF

This document specifies three methods for estimating the staining of organic finishes (subsequently referred to as “organic material”) by vulcanized or thermoplastic rubber, as defined in Clause 3 ....Read more :
— method A: contact staining and migration staining;
— method B: extraction staining;
— method C: penetration staining; Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • ...
  • 548
  • 549
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.