Metal scaffolding – Part 4: Temporary works equipment - Section 1: Scaffolds - Performance requirements and general design (First revision)

The adoption of the EN Standard as a Malaysian Standard was recommended by the Working Group on Tubular and Prefabricated Scaffolding under the authority of the National Standards Committee on Buildin ....Read more g, Construction and Civil Engineering. This Malaysian Standard is identical with EN 12811-1:2003, Temporary works equipment - Part 1: Scaffolds - Performance requirements and general design, published by the European Committee for Standardization (CEN). Close

RM 75.00

Vitreous china water closet pans – Specification (Fifth revision)

This Malaysian Standard specifies the quality, dimensional and functional requirements for three groups of water closet (WC) pans. The three groups of WC pans are as follows:

a) Group 1 ....Read more Close coupled and one-piece WC pan;
b) Group 2 Independent WC pan; and
c) Group 3 Hybrid WC pan.

The WC pans are further categorised into three types in relation to the quantity of water it requires to properly discharge the excrement from the water closet and ; this will encourage the development of water-efficient WC pan. The three types which link to the nominal full flush volume are 6 L, 5 L and 4 L. Close

RM 75.00

Household laundry detergent powder – Specification

This Malaysian Standard specifies the requirements and methods of analysis for household laundry detergent powder. It does not cover other special detergents like soakers, low suds, compact, etc. The ....Read more formulation of this detergent may contain one or more builders and/or other additives depending on the end use of the product. Close

RM 30.00

SPECIFICATION FOR PRECAST CONCRETE PIPES AND FITTINGS FOR DRAINAGE AND SEWERAGE PART 2 : SPECIFICATION FOR INSPECTION CHAMBERS AND STREET GULLIES

This Part of MS 881 specifies requirements for precast concrete inspection chambers, unreinforced or reinforced, for use over a drain or sewer not exceeding nominal size DN 250, in areas of light load ....Read more ing (see 3.5). This Part of MS 881 also specifies requirements for precast concrete street gullies. Close

RM 45.00

SPECIFICATION FOR PRECAST CONCRETE PIPES AND FITTINGS FOR DRAINAGE AND SEWERAGE PART 3 : SPECIFICATION FOR PIPES AND FITTINGS WITH OGEE JOINTS

This Malaysian Standard specifies requirements for two categories of precast concrete cylindrical unit, each with ogee (rebated) joints and unreinforced or reinforced with steel cages or hoops, namely ....Read more ‘Land drainage’ units and ‘Sewerage’ units.
Land drainage’ units are intended to be used primarily for land drainage and for the construction of culverts. ‘Sewerage’ units are intended to be used in conditions where more stringent requirements are necessary, for example in headings or in the construction of culverts where extra strength is required.
A range of nominal sizes (DN) is covered, namely DN 150 to DN 1800 by increments of 75 for ‘Land drainage’ units and ‘Sewerage’ units. Close

RM 60.00

SPECIFICATION FOR PRECAST CONCRETE PIPES AND FITTINGS FOR DRAINAGE AND SEWERAGE PART 1 : SPECIFICATION FOR PIPES AND FITTINGS WITH FLEXIBLE JOINTS AND MANHOLES

This Part of this MalaysianStandard covers precast concrete cylindrical pipes, bends and junctions with flexible joints, and also manholes, unreinforced or reinforced with steel cages or hoops, intend ....Read more edto be used forthe conveyance, under atmospheric pressure, of sewage or surface water, and for the construction of culverts.
Arange of nominal sizes (DN) of units is covered, namely DN 150 to ON 3000, by increments of 75.
A range of specified crushingtest loads is given for each nominal size of pipe Close

RM 105.00

Emergency preparedness and response (EPR) - Guidelines in managing emergencies in facilities

This Malaysian Standard specifies the minimum requirements for the development, implementation, maintenance, validation and improvement of emergencies for a facility in any sector or industry. It incl ....Read more udes the following:
a) The formation, purpose, responsibility and training of the top management team.
b) The determination of emergency situations including their risks.
c) The development of an emergency response plan including its processes.
d) The establishment, authority and training of an emergency structure.
e) The testing and validation of the emergency response plan.
f) Emergency related training.
This guideline applies to buildings, structures or workplaces occupied by people, with the exception of domestic buildings. Close

RM 75.00

Gas meters - Diaphragm gas meters (First revision)

This European Standard specifies the requirements and tests for the construction, performance, safety and production of class 1,5 diaphragm gas meters (referred to as meters) . This applies to meters ....Read more with co-axial single pipe, or two pipe connections, that are used to measure volumes of fuel gases, which are within the limits of test gases of the 1st, 2nd and 3rd families described in EN 437. The meters have maximum working pressures not exceeding 0,5 bar and maximum actual flow rates not exceeding 160 m3h−1 over a minimum ambient temperature range of −10 °C to 40 °C and a gas temperature range as specified by the manufacturer with a minimum range of 40 K. Close

RM 120.00

Repair and rehabilitation of pipeline

This Malaysian Standard gives requirements, guidance and recommendations for repair and rehabilitation method or technology of in-service liquid and gas pipelines for various anomalies.

....Read more This covers qualification and design, installation, testing, inspection, de-commissioning, re-commissioning, operation and maintenance of repaired and rehabilitated pipelines.

The liquid and gas pipelines shall be defined as per Petroleum (Safety Measures) Act 1984, Gas Supply Act 1993 and Gas Supply Regulations 1997.

The scope demarcation of these pipelines shall be as per ASME B31.4 and ASME B31.8 respectively.

This standard does not cover potable water pipelines.

This scope does not cover fabricated assemblies such as valves, fittings, launchers, receivers and cathodic protection system. Close

RM 60.00

Rubber, raw natural — Colour index test (ISO 4660:2020, IDT)

This document specifies two methods to determine the colour of raw natural rubber according to a standard colour scale:
— Method A: colour matching against standard coloured glasses;
â ....Read more €” Method B: colour determination using colour spectrophotometer.
In case of dispute, the preferred method is Method B. Close

RM 30.00