• :  
BM ENG
  • Home
  • Service
  • International Standard
  • FAQ
  • Publish
  • signin
  •  Cart ()
Search Malaysian Standard (MS)
 Advanced Search Search




Radio-frequency identification of animals - Code structure (ISO 11784:1996, IDT)
MS ISO 11784:2003 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard specifies the structure of the radio-frequency (RF) identification code for animals. RF identification of animals requires that the bits transmitted by a transponder are interp ....Read more retable by a transceiver. Usually the bit stream contains data bits, defining the identification code and a number of bits to ensure correct reception of the data bits. The standard specifies the structure of the identification code. Close

RM 15.00

Document will be sent via email



 Add To Cart
Information technology - Security techniques - Key Management - Part 1: Framework (First revision (ISO/IEC 11770-1:2010, IDT)
MS ISO/IEC 11770-1:2012
Status : 1st Revision
Format : PDF

This Malaysian Standard: 
a) establishes the general model on which key management mechanisms are based;
b) defines the basic concepts of key management which are common to all the parts ....Read more of MS ISO/IEC 11770;
c) specifies the characteristics of key management services;
d) establishes general principles on the management of keying material during its life cycle; and
e) establishes the conceptual model of key distribution. Close

RM 60.00

Document will be sent via email



 Add To Cart
RUBBER HOSES AND HOSE ASSEMBLIES FOR DISPENSING LIQUEFIED PETROLEUM GASES (LPGs) - SPECIFICATION (ISO 11759:1999, IDT)
MS ISO 11759:2005
Status : Original
Format : PDF

This Malaysian Standard specifies the requirements for flexible rubber hoses and hose assemblies used for the transfer of metered quantities of liquified petroleum gases (LPGs) from dispensing equipme ....Read more nt to motor vehicles. 
The hoses and hose assemblies specified in this International Standard are intended for use “wet”, i.e. permanently filled with liquid, in the temperature range from – 40 °C to + 60 °C.

The maximum working pressure is 20 bar (2 MPa). Close

RM 15.00

Document will be sent via email



 Add To Cart
RUBBER AND PLASTICS HOSES - EXPOSURE TO A XENON ARC LAMP - DETERMINATION OF CHANGES IN COLOUR AND APPEARANCE (ISO 11758:1995, COR. 1:1998, IDT)
MS ISO 11758:2008
Status : Original
Format : PDF

This Malaysian Standard specifies a method for exposing rubber and plastics hoses to a laboratory light source for the purpose of evaluating the changes in colour and appearance produced by such expos ....Read more ure. 
NOTE. A xenon arc was chosen from among a variety of sources since, when correctly filtered and maintained, it yields a spectrum closely similar to that of daylight. Close

RM 30.00

Document will be sent via email



 Add To Cart
BELT DRIVE - V-RIBBED BELTS FOR THE AUTOMOTIVE INDUSTRY - FATIGUE TEST (ISO 11749:1995, COR. 1:2003, IDT)
MS ISO 11749:2009
Status : Original
Format : PDF

This Malaysian Standard specifies a dynamic test method for the quality control of V-ribbed belts (PK profile) which are used predominantly for accessory drive applications in the automotive industry. ....Read more  The dimensional characteristics of the belts and of corresponding pulleys are the subject of IS0 9981. Close

RM 30.00

Document will be sent via email



 Add To Cart
Sterilization of medical devices - Microbiological methods - Part 2: Tests of sterility performed in the definition, validation and maintenance of a sterilization process (ISO 11737-2:2009, IDT)
MS ISO 11737-2:2011
Status : Original
Format : PDF

This Malaysian Standard specifies the general criteria for tests of sterility on medical devices that have been exposed to a treatment with the sterilizing agent reduced relative to that anticipated t ....Read more o be used in routine sterilization processing. These tests are intended to be performed when defining, validating or maintaining a sterilization process. 
This part of ISO 11737 is not applicable to:
a) sterility testing for routine release of product that has been subjected to a sterilization process;
b) performing a test for sterility;
c) culturing of biological indicators or inoculated products. Close

RM 30.00

Document will be sent via email



 Add To Cart
Anaesthetic and respiratory equipment - Supralaryngeal airways and connectors (ISO 11712:2009, IDT)
MS ISO 11712:2011 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard provides the essential requirements for the design of supralaryngeal airways and connectors. These devices are intended to open and seal the supralaryngeal area to provide an u ....Read more nobstructed airway in patients during spontaneous, assisted or controlled ventilation. 
This standard specifies the dimensions, basic properties and method of size designation of the available types of supralaryngeal airways. Airways devised for specialized applications are not specifically covered, although most may be classified by the sizing and dimensions (or other characteristics) required by this standard.

The following devices are outside the scope of this standard: nasal and oropharyngeal
airways, anesthetic masks, oro- and naso-tracheal tubes, cricothyrotomy devices, dental appliances, tracheal stents, tracheal tubes, ventilating laryngoscopes, CPAP devices, esophageal obturators, bougies and devices that require surgical placement.

This standard requires dimensional disclosu Close

RM 60.00

Document will be sent via email



 Add To Cart
Statistical aspects of sampling from bulk materials - Part 2: Sampling of particulate materials (ISO 11648-2:2001, IDT)
MS ISO 11648-2:2004 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard establishes the basic methods for sampling particulate materials in bulk (e.g. ores, mineral concentrates, coal, industrial chemicals in powder or granular form, and agricultur ....Read more al products such as grain) from moving streams and stationary situations, including stopped-belt sampling, to provide samples for measuring one or more variables in an unbiased manner and with a known degree of precision. The variables are measured by chemical analysis and/or physical testing. These sampling methods are applicable to materials that require inspection to verify compliance with product specifications or contract settlements, to calculate the value of the lot mean of a measurable quantity as a basis for settlement between trading partners, or to estimate the set of variables and variances that describes a system or procedure. Close

RM 165.00

Document will be sent via email



 Add To Cart
STATIONARY SOURCE EMISSIONS - DETERMINATION OF MASS CONCENTRATION OF SULFUR DIOXIDE - ION CHROMATOGRAPHY METHOD (ISO 11632:1998 (2004), IDT)
MS ISO 11632:2009
Status : Original
Format : PDF

This Malaysian Standard specifies a method for the determination of the mass concentration of sulfur dioxide emitted from combustion facilities and technical processes, and defines the most important ....Read more performance characteristics. 
The method described in this Malaysian Standard has been tested for a sulfur dioxide concentration range of 6 mg/m3 to 333 mg/m3 with sampling periods of 30 min. It is applicable to mass concentrations of sulfur dioxide exceeding this range by carrying out an appropriate dilution of the sample solutions prior to the analysis or by using larger volumes of absorption solution, and to sulfur dioxide concentrations below this range by extending the sampling period.

This Malaysian Standard is applicable to the analysis of samples containing negligible levels of sulfur trioxide and volatile sulfates (< 5 % of the expected sulfur dioxide concentration), and ammonia (< 5 mg/m3). All concentrations are based on dry gas at a temperature of 273,2 K and pressure of 101, Close

RM 30.00

Document will be sent via email



 Add To Cart
Gas cylinders - Procedures for change of gas service (ISO 11621:1997, IDT)
MS 11621:2008 (CONFIRMED:2015)
Status : 1st Confirmation
Format : PDF

This Malaysian Standard applies to seamless steel, aluminium alloy and welded steel refillable cylinders of all sizes, including large cylinders (water capacity greater than 150 L). It provides genera ....Read more l requirements and procedures to be considered whenever a cylinder is being transferred from one gas service to another for permanent and liquefied gases.It does not apply to cylinders for dissolved acetylene, radioactive gases or gases listed in group G of table 1. Close

RM 30.00

Document will be sent via email



 Add To Cart
  • ‹
  • 1
  • 2
  • ...
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • ...
  • 548
  • 549
  • ›
©2020 All rights reserved
Department of Standards Malaysia (STANDARDS MALAYSIA). Best viewed on latest browser.